For a modern and stylish feel, Steel Clad 762 is the perfect solution. Made from high tensile steel, this lightweight cladding material is engineered to provide the highest rigidity possible, while using the least material.
Manufactured locally using quality Colorbond® or Zincalume® steel, Steeline Steel Clad is strong and long lasting.
As specialists in all things steel, we can assist with your entire project from start to finish. From ideas to advice, installation and everything in between, Steeline offers a full range of services to make projects a breeze.
Not sure where to start? Our trained experts can answer any questions, no matter how big or small. You can call your local Steeline team for advice, or request a free quote anytime.
Manufactured right here in Australia from only the best BlueScope steel, our tried and tested products are guaranteed to last well into the future.
Sheets of Steeline Steel Clad overlap each other and are fixed progressively along the building in the opposite direction to the prevailing weather. This gives complete weather protection and a fast and efficient method of installing the roof. Each sheet consists of an “over” rib and an “under” rib, and when put together they form an anti-capillary drain, which prevents water entry.
Lift packs of Steeline Steel Clad onto the roof frame so that all sheets are the right way up and with the over edge facing the end of the roof where laying will commence. Prevent roof damage by walking only in the pans of the sheets and stand on the ribs only at supports. When the roof pitch is less than 15° or where there are extreme weather conditions, turn the sheet ends up approx. 80° at the high end and down approx. 15° at the gutter or low end. A turn up/down tool is used to do this.
When two or more sheets are required for full length cover, start laying at the gutter and work up to the ridge and then start the next run. The minimum end laps required are:
Roofs Pitch up to 15° 230mm
Pitch over 15° 150mm
End laps in roofs with a pitch of <5° (1 in 12) are to be sealed. End laps must be positioned over a support and the support spacings either side are to be that recommended for an end span.
Steel Framing (up to 5mm):
A. Crest Fixed No 12×45 or a 14×50 Hex Head Self Drilling Tek with neo washer
B. Valley Fixed No 10×16 Hex Head Self Drilling Tek with neo washer C. As screw manufacturers have further developed their product you can now use a combination screw that will screw into timber or metal depending on the thickness of metal. Ask your Steeline member for a recommended fixing screw to suit your purpose.
A. Crest Fixed No 12×65 or a 14×65 Hex Head Type 17 Self Drilling Wood Screw with neo washer.
B. Valley Fixed No 10×22 or a 12×22 Hex Head Type 17 Self Drilling Wood Screw with neo washer
C. A s screw manufacturers have further developed their product you can now use a combination screw that will screw into timber or metal depending on the thickness of metal. Ask your Steeline member for a recommended fixing screw to suit your purpose.
Side lap fasteners
Side lap fasteners are to be added at the midspans of sheets for support, where spacing are over 900mm for roofs and 1200mm for walls to give weatherproofing. Use No 8×12 hex head type S self drilling screw with neo washer or blind rivets.
Methods of fixing
Roofs Pierce fix through crests only using 1 fastener through every rib at every support ( 4 Fasteners/sheet).
Walls Crest fixing as for roofs OR Valley fixing can be used. Valley fixing requires 1 fastener beside every rib at every support (4 Fasteners/ Sheet). If valley fastening is used, side lap fasteners must be added beside each main fastener.
When unloading bundles of sheeting with a crane always use a spreader bar and fabric slings to prevent damage. When manually handling sheets use clean dry gloves and do not drag sheets over each other. Storage of sheets should be above ground and under cover.
Crest fasteners must not be over-tightened but driven in until slight deformation of the rib is observed and the neoprene washer is fully sealed. Do not locate fasteners less than 25mm from the end of sheets. Do not use punches to form holes for fasteners. Holes are to be drilled or self drilling fasteners are to be used.
Steeline Steel Clad has an effective coverage of 762mm when laps of one rib are used.
The normal recommended minimum roof slope is 1 in 20 (approximately 3°). However, in non-cyclonic areas where roofs are in single sheet lengths, with a run of less than 15 metres, a minimum roof slope of 1 in 30 (approximately 2°) may be used.
Additional information available at: