Round Flo

Steeline RoundFLo Gutters are designed to compliment stylish and contemporary buildings, but also looks great on older style, period homes.

Steeline RoundFLo Gutters can be supplied with or without slots to protect your home from water overflow.

Made from quality Colorbond® or Zincalume® steel, Steeline RoundFlo Gutters are strong and long lasting.

*Please note: The exact dimensions of each product may vary slightly between stores so if you need to match your existing profile please check with your local branch before ordering*

View COLORBOND® steel colours

Projects made easy

Projects made easy

As specialists in all things steel, we can assist with your entire project from start to finish. From ideas to advice, installation and everything in between, Steeline offers a full range of services to make projects a breeze.

Free expert advice

Free expert advice

Not sure where to start? Our trained experts can answer any questions, no matter how big or small. You can call your local Steeline team for advice, or request a free quote anytime.

Superior quality and performance

Superior quality and performance

Manufactured right here in Australia from only the best BlueScope steel, our tried and tested products are guaranteed to last well into the future.

Installation

Fixing to timber fascia
Fix a bracket at the high end of fall first, then fix a bracket at the low end of the fall. Stringline a common datum on both brackets and install the remaining brackets at the required spacings (not exceeding 900mm), with common datum on the stringline.

The brackets are best attached to the fascia with the use of 12 x 25 wafer T17 class 3 self drilling screws.

Attaching gutter to internal (Roundflo only) brackets
Hook the front of the gutter onto the end of the long arm of the brackets and slide the back of gutter under the long arm until it is hard up to the back of the bracket. Push the gutter into the upright position. When the gutter is in the correct position, turn down both tabs of the gutter brackets onto the back of the gutter, completing the attachment.

Fixing Half Round with external brackets
Lift gutter into external bracket. Position correctly for corners and stop ends and ensure that bead hooks into the bead mould on the external bracket.

Spring Clip System (Roundflo only)
Fixing to metal fascia is made incredibly simple by using the Steeline spring clip. The clip snaps over the metal fascia and has six teeth at alternative heights. The fall of gutter to downpipe outlet is determined by the height of where the gutter is attached to these teeth. The face of gutter is then supported by the Steeline overstraps, which connect to the front bead of gutter and top bead of fascia.

Support Recommendations

Gutter brackets are to be placed at stop ends and between stop ends at intervals of no more than 900mm. Where metal fascia is used, brackets must be placed within 150mm either side of the rafter brackets.

Stop Ends
Pre-formed stop ends provide a neat finish to straight runs of gutter and require less labour and skill than site formed ends. However both methods of end stopping require the use of rivets and a roofing type silicone sealant.

stop ends

External Corners

When cutting the gutter lengths, allow an extra 165mm past the outside fascia. Cut the gutter ends at 45° as shown. Fix external and internal corner over mitred cuts, use rivets or screws and silicon. For 45° corners cut gutter at 22.5°.
*For external corners in 150, allow extra 15mm on mitre cut to slip inside the opposite mitre cut for riveting and sealing.

Internal Corners

When cutting gutter lengths, allow for the gutter to go right up to the adjoining fascia. Cut gutter ends at 45° as shown. Assemble in a similar manner to external corners. For 45° corners cut gutter at 22.5°.
*For internal corners in 150, allow extra 15mm on mitre cut to slip inside the opposite mitre cut for riveting and sealing.

Gutter Joining

Reduce the top rib for 25mm to allow for a slip joint. Slide the reduced end into the other end, applying a suitable sealant, then blind rivet together.

 

Additional information available at: